How to plug the computer host boot cable into the motherboard

How to illustrate the computer boot cable

First connect the power cord from the chassis, one of which is wider, as shown by the arrow in the picture below. If it's labeled USB, it's the cable that connects to the USB slot on the case panel. Find the USB pin on the edge of the motherboard and plug it in.

Corresponds to the RESET jack on the motherboard. The SPEAKER above is the front alarm speaker interface of the chassis. We can see that it has a four-pin structure. The red line is the 5V power supply line and is connected to the motherboard. Corresponding to the 5V interface, the other three pins can be easily inserted.

The connection method of computer startup cable is as follows: Power switch: white positive pole, brown-negative pole can be plugged forward or reverse. Reset switch: white and blue in two colors, can be plugged forward or reverse. Power indicator light: The green one is plugged into the P LED pin, the white one is plugged into the P LED- pin.

To plug the network cable into the computer, you need to first find the interface of the network cable broadband box, then insert one end of the network cable, then find the interface that matches the computer and the network cable, and insert the other end of the network cable.

How to connect the power-on button wire on the computer motherboard: Put all the wires together. According to the above label, first clarify the definition of each wire: a. Power switch: POWER SW, which may be named : POWER, POWER SWITCH, ONOFF, POWER SETUP, PWR, etc. Function definition: Reset button on the front of the chassis.

How to connect the desktop computer host’s boot cable: Put all the cables together. According to the above labels, first clarify the definition of each cable: a. Power switch: POWER SW, POWER, POWER SWITCH, ONOFF, POWER SETUP, PWR, etc., function definition: reset button on the front of the chassis.

How to connect the wire inside the desktop computer’s power-on button to the motherboard

How to connect the desktop computer host’s power-on cable: Arrange all the cables together, and first clarify them according to the above markings Definition of each wire: a. Power switch: POWER SW, POWER, POWER SWITCH, ONOFF, POWER SETUP, PWR, etc. Function definition: Reset button on the front of the chassis.

First, find the PWR SW or Power Switch pin socket and determine where the power-on key wire needs to be inserted. Insert the copper pin on the power button wire into the PWR SW pin socket. If you have a second pin socket on your computer's motherboard, you can repeat this step to connect another copper pin.

First of all, the motherboard supplies power. Currently, most motherboards have 24PIN interfaces. There are also 24PIN interfaces in the power supply, which can be plugged in accordingly. After the motherboard power supply connection is completed, connect the installed CPU power supply 4PIN interface to the corresponding slot position.

How to connect the power-on button wire on the computer motherboard: Put all the wires together. According to the above label, first clarify the definition of each wire: a. Power switch: POWER SW, which may be named : POWER, POWER SWITCH, ONOFF, POWER SETUP, PWR, etc. Function definition: Reset button on the front of the chassis.

How to connect the wire inside the desktop computer’s power button to the motherboard

The motherboard generally has four sets of switch indicator wires, POWER SW power switch. POWER LED power indicator light. RESET SW reset switch. H.D.D LED keyboard status indicator. Pay attention to the positive and negative poles when connecting. Usually, colored lines such as red, green, and yellow represent the positive pole, and white and black represent the negative pole. Pay attention to the distinction.

How to connect the desktop computer host’s boot cable: Put all the cables together. According to the above labels, first clarify the definition of each cable: a. Power switch: POWER SW, POWER, POWER SWITCH, ONOFF, POWER SETUP, PWR, etc., function definition: reset button on the front of the chassis.

First, find the PWR SW or Power Switch pin socket and determine where the power-on key wire needs to be inserted. Insert the copper pin on the power button wire into the PWR SW pin socket. If you have a second pin socket on your computer's motherboard, you can repeat this step to connect another copper pin.

How to plug the few wires into the motherboard when the computer is turned on

Arrange all the wires together. According to the above labels, first clarify the definition of each wire: a. Power switch: POWER SW, POWER, POWER SWITCH, ONOFF, POWER SETUP, PWR, etc., function definition: reset button on the front of the chassis.

The motherboard generally has four sets of switch indicator lines and POWER SW power switch. POWER LED power indicator light. RESET SW reset switch. H.D.D LED keyboard status indicator. Pay attention to the positive and negative poles when connecting. Usually, colored lines such as red, green, and yellow represent the positive pole, and white and black represent the negative pole. Pay attention to the distinction.

First of all, the motherboard supplies power. Currently, most motherboards have 24PIN interfaces. There are also 24PIN interfaces in the power supply, which can be plugged in accordingly. After the motherboard power supply connection is completed, connect the installed CPU power supply 4PIN interface to the corresponding slot position.

How to plug the computer switch cable into the motherboard

Arrange all the cables together. According to the above markings, first clarify the definition of each wire: a. Power switch: POWER SW, POWER, POWER SWITCH, ONOFF, POWER SETUP, PWR, etc., function definition: reset button on the front of the chassis.

First of all, among the power cords connected from the chassis, there is a relatively wide one, as pointed by the arrow in the picture below. If it is marked USB, then it is connected to the USB socket on the chassis panel. For the cable, look for the USB pin on the edge of the motherboard and just plug it in. This one is relatively large and easy to find.

The motherboard generally has four sets of switch indicator lines and POWER SW power switch. POWER LED power indicator light. RESET SW reset switch. H.D.D LED keyboard status indicator. Pay attention to the positive and negative poles when connecting. Usually, colored lines such as red, green, and yellow represent the positive pole, and white and black represent the negative pole. Pay attention to the distinction.

The computer case has a bunch of wires with plugs. These plugs are marked with power on, reset, speak and other characters. Power on is the plug corresponding to the switch wire, and reset is the plug corresponding to the reset button.

First connect the power cord from the chassis, one of which is wider, as shown by the arrow in the picture below. If it's labeled USB, it's the cable that connects to the USB slot on the case panel. Find the USB pin on the edge of the motherboard and plug it in.

The above is the detailed content of How to plug the computer host boot cable into the motherboard. For more information, please follow other related articles on the PHP Chinese website!