Help, what should I do if my computer cannot access the Internet?

Help! What should I do if my computer cannot access the Internet and cannot connect to the Internet? PHP editor Baicao brings you the reasons and solutions for why your computer cannot access the Internet. Please read below for details.

1. Help, what should I do if my computer cannot access the Internet?

Disable Ethernet

Then restart the computer

Enable Ethernet and try again.

The second method

1, click the start menu, run

2, enter CMD and press Enter.

3. Enter: netsh winsock reset catalog and press Enter.

4. Enter: netsh int ip reset reset.log and press Enter.

5. Click the start menu, shut down or log out and restart. Then the computer can be turned on.

If it still doesn’t work, there is no other way

2. The computer cannot access the Internet after wireless bridging?

When using WDS bridging router, the system shows that the bridging is successful, but the Internet cannot access the Internet normally. In most cases, it is related to the settings of the primary and secondary routers.

The same channel is not selected

While most routers will synchronize their own channels with the main router when WDS bridging, there are still a few routers that need to be set up manually.

Therefore, when two routers show that the bridge is successfully connected but cannot access the Internet, you should first check whether the channels are the same. Routers on different channels cannot communicate with each other even if the bridge is successful.

IP address not changed

The secondary router is the wireless router used to enable the WDS function. It has the same functions as the main router and has an independent IP address.

Most operators will ignore the IP address of the secondary router. The secondary router application that is successfully bridged has the IP address of the same network segment as the primary router and cannot conflict with other devices.

For example, if the IP address of the primary router is 192.168.3.1 and the DHCP address pool is

192.168.3.100-192.168.3.200, then after the secondary router is successfully bridged, the LAN port IP address of the secondary router should be manually changed to 192.168. 3.X.

When setting, the IP address of the secondary router cannot be a gateway, and the value of X should be outside the DHCP address pool. For example, the IP address of the secondary router can be set to 192.168.3.254.

DHCP is not turned off

Except that the IP address of the secondary router cannot conflict with the settings in the primary router network, the secondary router as a transit device cannot enable the DHCP service.

DHCP, Dynamic Host Configuration Protocol. This service is responsible for allocating valid IP addresses to devices connected to the network and providing gateway, DNS and other services.

In the same network, if there are two DHCP servers, the device connected to the network later will not be able to obtain a valid IP address.

Therefore, when the WDS bridge is successfully connected and the LAN address is set for the secondary router, the DHCP service of the secondary router should be turned off to restore the Internet access function.

3. Change the wifi password. Can’t access the Internet on your desktop computer?

After we use one or several wifi for a long time, the computer will automatically connect every time it detects a wifi signal. When we change the password, the computer will not prompt for an incorrect password after connecting to wifi, nor will it pop up to enter the password. The window will only show that it cannot connect. What should we do at this time?

Start the computer, select "Network" on the desktop, then right-click the mouse and select "Properties"

In the properties window, select "Manage Wireless Networks" You can clearly see that there are many wireless networks saved. Now we select our Right-click the wireless network that changed the password and select "Delete Network"

After deleting the network, now we have to click on the wireless icon in the lower right corner of the computer, select the wireless signal for which you have changed the password, click Connect, and now you will be prompted Enter your password!

4. How to configure the IP address when the computer cannot access the Internet?

1. Use IE to log in to the routing settings page. The default should be 192.168.1.1. The default account is admin and the password is admin (usually this is the case).

2. Follow the wizard’s prompts to set it up again correctly. If the network gateway of the routing chain does not exist To enable the DHCP service, select a static address. If it is enabled, select automatic acquisition. If it is a static address, you need to enter the correct DNS address to access the Internet normally (pay attention to check this item).

3. Check if there are any problems with other routing settings.

4 .If you want to manually configure the local IP, turn off the DHCP service of the router and set the IP address manually. Note: The DNS address of the manually set IP must be the same as the DNS obtained or set by the router, otherwise the web page cannot be opened. 5. If the router is turned on DHCP service, then the local only needs to be set to automatically obtain an IP.

5. Common reasons and solutions for computers unable to access the Internet

Computers unable to access the Internet is a very common problem, which may be caused by a variety of reasons. As a professional website editor, I will introduce you to the common reasons why your computer cannot access the Internet in detail, and provide corresponding solutions to help you restore your network connection as soon as possible.

Common causes and solutions

1. Network adapter driver problem

If there is a problem with the computer's network adapter driver, it may result in the inability to access the Internet. You can try the following steps to solve it:

Open the device manager and check whether the network adapter is displayed normally. If there is an exclamation mark or question mark, it means there is a problem with the driver. Uninstall and reinstall the network adapter driver. You can download the latest version of the driver from the official website of the computer manufacturer or network adapter manufacturer. If the above method cannot solve the problem, you can consider replacing the network adapter hardware.

2. Network setting issues

Incorrect network settings on your computer may also result in the inability to access the Internet. You can try the following steps to solve the problem:

Check whether the network connection is normal, including network cables, routers and other hardware devices. Check whether network parameters such as IP address and DNS settings are correct. You can try setting it manually or using automatic acquisition. Check your firewall and anti-virus software settings to make sure they are not blocking network connections. If it is a wireless network, check whether the wireless network card is turned on and whether the signal strength is sufficient.

3. Virus or malware infection

If your computer is infected by a virus or malware, it may also cause you to be unable to access the Internet. You can try the following steps to solve the problem:

Use anti-virus software to perform a comprehensive scan to find and remove viruses or malware. If it cannot be solved through anti-virus software, you can consider reinstalling the operating system.

4. Network service provider problem

If none of the above methods can solve the problem, there may be a problem with the network service provider. You can try the following steps:

Check the service status of the network service provider, whether there is a line failure or maintenance. Contact your network service provider's customer service to report the problem and ask for help.

In short, there may be many reasons why the computer cannot access the Internet, which need to be investigated and solved according to the specific situation. I hope the above methods can help you restore your network connection as soon as possible. If you have any other questions, please feel free to contact me. Thank you for reading!

6. The computer screen suddenly goes black, and then the computer cannot access the Internet?

You can try to troubleshoot as follows:

1. Restart the computer. A bug in the system will cause network connection failure. Restart the computer and then connect again;

2. Check the wireless router or the connection between the modem and the external network. Connect the cable and check whether the indicator light flashes normally. Power off the router and modem for a few minutes and then power on and restart to see if the fault is solved;

3. Disable the computer's wireless network card driver and restart it. If the fault still exists, it is recommended to uninstall it. After installing the wireless network card driver, reinstall the wireless network card driver of the corresponding adapted model;

4. Skip the wireless router and directly connect the modem to the computer for broadband dial-up Internet access. If broadband dial-up cannot access the Internet normally, it is recommended to call the operator's customer service directly. Report for repair;

5. Use other electronic devices to connect to the same wifi, enter the password to log in, and see if it can be used normally. If not, restore the wireless router to factory settings, reset the Internet parameters, and then connect.

7. What should I do if my Xiaomi tablet cannot access the Internet?

Solution for Xiaomi phone not being able to access the Internet:

1. Restart the phone;

2. Drag down from the top of the screen (or drag from bottom to top), make sure "Mobile Data" is on and "WLAN" is off Status;

3. Enter the phone in turn - (or dual SIM card and mobile network) - select the name of the card that needs to be connected to the Internet, keep the card slot you want to use open, click - click the menu button "Reset to default settings" that is Yes (whether the traffic fee generated by the cmnet access point is included in the package shall be subject to the actual activated package);

4. If you still cannot access the Internet after setting it up, it is recommended to change the phone and card for testing.

8. After resetting the router, the computer cannot access the Internet?

After resetting the router, the computer cannot access the Internet. You must reset the router before you can access the Internet. The connection setting method after the router is reset is as follows:

1. Connect the broadband bus (the network cable from the modem) to the WAN port of the router.

2. Connect one end of the network cable to any LAN port of the router, and the other end to the computer, start the computer and router device;

3. After starting the device, open the browser and enter 192.168.1.1 in the address bar to enter the wireless router setting interface.

4. An account and password for logging into the router will appear on the setting interface. Enter the default account and password admin5. Set up step by step according to the setting wizard and select the Internet access method. Usually ADSL users choose the first item PPPoE. If they are using other networks The service provider will choose the following two items according to the actual situation. If you don’t know how to choose, just select the first item and choose automatically, which is convenient for novices. After selecting, click Next; 6. Enter the account number applied for from the network service provider and password, go to the next step after completing the input; 7. Set the wifi password, and try to make the alphanumeric combination more complex to prevent it from being used. 8. After the input is correct, you will be prompted whether to restart the router. Select Yes to confirm to restart the router. After restarting the router, you can access the Internet normally.

9. Can’t access the Internet when connecting the Huawei optical modem to the computer?

First, there is a problem with the fiber optic signal. At this time, the optical signal indicator light should light up on the optical modem, indicating that the fiber optic signal is faulty. This kind of problem can only be solved by calling customer service to report it for repair.

Second, there is a problem with the connection between the computer and the optical modem. When connected normally, both the Optical Modem LAN port light and the computer network card light should flash normally. If there is a problem with the connection, the light will not light up.

Third, the computer itself has problems, such as DNS or system failure. It is recommended to try another computer.

10. Tidak boleh mengakses Internet apabila hotspot iPhone 11 disambungkan ke komputer?

Penyelesaian kepada masalah bahawa iPhone tidak boleh mengakses Internet apabila ia menghidupkan hotspot dan menyambung ke komputer.

1. Semak sama ada peranti lain di rumah boleh menyambung ke Internet Jika tidak, sila hubungi operator rangkaian Jika mereka boleh menyambung, sila pergi ke langkah seterusnya.

2. Rujuk manual penghala untuk menetapkan semula Apabila penghala menetapkan alamat Mac dan mengikat alamat IP, ia akan menjejaskan akses telefon mudah alih ke Internet.

3. Jika anda menggunakan berbilang peranti di rumah untuk menyambung ke penghala yang sama, adalah disyorkan untuk merujuk kepada parameter yang diberikan oleh penghala dan menetapkan alamat IP tetap untuk setiap peranti untuk mengelakkan konflik alamat IP.

4. Adalah disyorkan untuk memasuki penghala, kemudian tetapkan DNS kepada DNS tempatan terpantas, dan kemudian tetapkan telefon untuk mendapatkan IP secara automatik.

5 Adalah disyorkan untuk memulihkan penghala wayarles ke tetapan kilang dan kemudian cuba menyambung dengan iPhone sekali lagi. Dalam keadaan biasa, alamat log masuk tetapan penghala wayarles ialah: 192.168.1.1.

The above is the detailed content of Help, what should I do if my computer cannot access the Internet?. For more information, please follow other related articles on the PHP Chinese website!