Laptop battery not charging when plugged in
Why does the computer show that the power is connected but not charged?
Poor contact and battery damage The battery has a number of charges and a service life. If the service life and number of charges are exceeded, Of course, the battery will be disconnected and unable to charge. Sometimes the computer's charging port may become loose, preventing the battery port from being connected.
The reasons are as follows: Check whether the charging function is disabled. The notebook has a "disable charging" function in the battery options. Under this function, the adapter directly supplies power to the notebook without charging the battery. In this case, it is charging. No electricity.
Circuit failure Sometimes the circuit is unstable or the voltage is too high or too low, which will affect the charging of electronic equipment. In particular, some electronic equipment cannot be directly connected to the circuit socket, or must go through a specific adapter. These These are all possible reasons for this situation.
% of the available power supply is connected and not charging. Analysis of the reasons: 1. Most of the reasons for this phenomenon of laptop batteries are due to the aging of the laptop battery or the lack of daily maintenance. For example, many friends’ laptop batteries often drain the battery power. Use it until it is exhausted and the computer shuts down automatically, which can easily damage the battery.
The laptop battery is 0%, but the power is connected and it is not charging. It may be due to incorrect computer settings. The specific solution is as follows: Click the power icon. Click. Click.
Restart and try to see if it can charge normally. If after checking that the computer battery charging is not disabled, and the power still shows that it is connected but not charging, unplug the power plug and plug it in again. Remove the laptop battery and reinstall it, shut down the computer system for a period of time and then restart.
Why is the laptop power light on but it says not charging?
Cause analysis: The reason may be that the battery has not been charged for a long time, resulting in serious power loss after the internal power of the battery is used up. It's just a computer charging protection to prevent overcharging. As long as you set the battery options, the problem can usually be solved.
The last problem that may cause the laptop to be unable to charge is the power adapter failure, but it is very rare and there is no suitable self-test method. It can only be sent to a repair station for testing.
The reason for this may be that the battery has not been charged for a long time, resulting in serious power loss after the internal power of the battery is exhausted. It is just a protection for computer charging to prevent overcharging. As long as you set the battery options, it is generally sufficient. Problem solved. Check to see if you are using the original battery.
What should I do if the Lenovo computer shows that the power is connected but not charging? The reason for this may be that it has not been charged for a long time, resulting in serious power loss after the internal power of the battery is exhausted. This is just the protection of the computer charging and does not allow it to overcharge. It's just charging. Just setting the battery options can usually solve the problem.
Recently, many friends have reported to us that after plugging in their win10 laptops, the battery indicator light is on and the power supply is connected, but it always shows that it is not charging. I don’t know what’s going on. I’m too worried. Friends who have this problem should take a look at the specific steps below and give it a try.
It is recommended to turn off the phone and then charge again. Check the change of the light on the right. It should be flashing and flashing during the charging process. If it still has no effect after turning off the phone and charging for ten minutes, the battery may be faulty. It is recommended to send it to Have it checked by a repair station.
The laptop shows that it is connected to the power supply, why is it not charging?
It may be that the computer is stuck and does not show charging. Solution: You can restart the computer and try charging again, or upgrade the computer system. The laptop's battery is damaged, causing the computer to connect directly to an external power source instead of using the power in the battery. Solution: It is recommended to contact after-sales service for maintenance.
It is caused by poor contact of the laptop battery. It is recommended to shut down the computer, plug in and remove the battery, and then turn it back on to check the system. It is caused by low battery voltage protection. It is recommended to use a hair dryer to heat the battery for a few minutes before connecting it to the computer for charging.
The reason for this may be that the battery has not been charged for a long time, resulting in serious power loss after the internal power of the battery is exhausted. It is just a protection for computer charging to prevent overcharging. As long as you set the battery options, it is generally sufficient. Problem solved.
The main reasons for the prompt "The power is connected but not charging" are as follows: The notebook power connection is in poor contact. The internal battery of the notebook is damaged. The power mode sets the best battery maintenance, and it will not charge when it reaches 50%.
The reason why the laptop is plugged in and not charging: The laptop battery is between 95% and 99%. When the adapter is plugged in, it will not charge (not all brands have this design). This is to prevent the battery from recharging. Protection measures for charging.
Why is the laptop battery not charging?
The laptop battery is damaged, causing the computer to directly connect to an external power source instead of directly using the power in the battery. Solution: It is recommended to contact after-sales service for maintenance.
Circuit failure Sometimes the circuit is unstable or the voltage is too high or too low, which will affect the charging of electronic equipment. In particular, some electronic equipment cannot be directly connected to the circuit socket, or must go through a specific adapter. These These are all possible reasons for this situation.
The reason for this situation may be that the battery has not been charged for a long time, resulting in serious power loss after the internal power of the battery is exhausted. The reason is analyzed as follows: Check the laptop battery settings to see if battery charging is disabled. Some laptop battery management software also disables the charging function. You can check it.
The main reasons for the prompt "The power is connected but not charging" are as follows: The notebook power connection is in poor contact. The internal battery of the notebook is damaged. The power mode sets the best battery maintenance, and it will not charge when it reaches 50%.
The battery has a number of charges and a service life. If the battery exceeds the service life and the number of charges, it will of course become disconnected and fail to charge. Sometimes the computer's charging port may become loose, preventing the battery port from being connected.
% of the available power supply is connected and not charging. Analysis of the reasons: 1. Most of the reasons for this phenomenon of laptop batteries are due to the aging of the laptop battery or the lack of daily maintenance. For example, many friends’ laptop batteries often drain the battery power. Use it until it is exhausted and the computer shuts down automatically, which can easily damage the battery.
What’s going on when the computer shows that the power supply is connected but not charging?
The reason is as follows: Check whether the charging function is disabled. The notebook has a "disable charging" function in the battery options. Under this function, the adapter is directly Powering the laptop without charging the battery will not charge the battery in this case.
A damaged charger may also cause the power connection to fail to charge. Try another charger of the same brand. If it is the charger, replace it. It is possible that the battery is not installed or the battery is loose and cannot be connected to the computer interface. If it is loose, just reinstall it.
The computer displays "Power is connected but not charging", which means that the power is connected, but the computer battery is not charging. There are several reasons for this failure: Battery damage. It is caused by problems with the charging and discharging circuit of the board. Sometimes the aging of the power supply itself and insufficient power supply can also cause the failure to charge.
, The charger and battery are loose. A damaged charger may also cause the power connection to fail to charge. Try another charger of the same brand. If it is the charger, replace it. It is possible that the battery is not installed or the battery is loose and cannot be connected to the computer interface. If it is loose, just reinstall it.
It may be that the computer is lagging and charging is not displayed. Solution: You can restart the computer and try charging again, or upgrade the computer system. The laptop's battery is damaged, causing the computer to connect directly to an external power source instead of using the power in the battery. Solution: It is recommended to contact after-sales service for maintenance.
The above is the detailed content of Laptop battery not charging when plugged in. For more information, please follow other related articles on the PHP Chinese website!

Hot AI Tools

Undresser.AI Undress
AI-powered app for creating realistic nude photos

AI Clothes Remover
Online AI tool for removing clothes from photos.

Undress AI Tool
Undress images for free

Clothoff.io
AI clothes remover

Video Face Swap
Swap faces in any video effortlessly with our completely free AI face swap tool!

Hot Article

Hot Tools

Notepad++7.3.1
Easy-to-use and free code editor

SublimeText3 Chinese version
Chinese version, very easy to use

Zend Studio 13.0.1
Powerful PHP integrated development environment

Dreamweaver CS6
Visual web development tools

SublimeText3 Mac version
God-level code editing software (SublimeText3)

Hot Topics











The computer has a restore point, and when the system is restored, it prompts "You must enable system protection on this drive." This usually means that the system protection function is not turned on. System protection is a feature provided by the Windows operating system that can create system restore points to back up system files and settings. That way, if something goes wrong, you can revert to a previous state. When the system fails and you cannot enter the desktop to start it, you can only try the following method: Troubleshooting-Advanced Options-Command Prompt Command 1 netstartvssrstrui.exe/offline:C:\windows=active Command 2 cd%windir%\system32 \configrenSYSTEMsy

A problem that Windows 10 users may encounter is that they cannot find the switch user option on the login interface. So what should I do if there is no switch user option on the win10 login interface? Let this site give users a detailed explanation of the problem of not switching user options in the win10 login interface. Detailed solution to the problem of switching user options on the Win10 login interface: Check user account settings: First, make sure you have multiple user accounts on your computer and that these accounts are enabled. You can check and enable the account by following these steps: a. Press Win+I keys to open Settings and select "Accounts". b. Select "Family & Others" or &ld in the left navigation bar

Although the comprehensive anti-virus software that comes with Windows 10 system can continuously protect the security of your personal computer, sometimes it may also affect certain downloaded files. For some users, it may be more appropriate to temporarily turn off the real-time protection function. But many users don’t know how to permanently turn off the real-time protection feature on win10 system. 1. First, press the "Win+R" keys to open the run window, enter the "gpedit.msc" command to open the local Group Policy Editor interface; 2. Then, in the opened interface, click "Computer Configuration/Administrative Templates/ Windows Components/MicrosoftDef

In Windows 10 system, if you want to return to the system default wallpaper, you can follow the following steps: 1. Right-click a blank space on the desktop and select Personalize in the pop-up menu. 2. This will open the Personalization window in Settings. In the left menu, click Background. 3. Under the "Background" settings, find and click the drop-down menu next to "Choosepicture", and then select Windows Default (Windows Default) or directly select a picture that looks like the default wallpaper in the picture preview below ( if there are multiple options). 4. If your system has multiple versions

The guy's computer appears: Windows cannot start the WindowsAudio service (located on the local computer). Error 0x8007005: Access denied. This situation is usually caused by user permissions. You can try the following methods to fix it. Method 1: Modify the registry to add permissions through batch processing, create a new text document on the desktop, save it as .bat, and right-click the administrator to go far. Echo==========================EchoProcessingRegistryPermission.Pleasewait...Echo================== ========subinacl/subkey

There are many reasons why the screenshot disappears after taking a screenshot in Win10. Users can first check the screenshot save location or adjust the screenshot settings, or check the animation effect to check it. If it really doesn't work, you can also choose to update the driver and operating system to perform the operation. Let this website carefully introduce to users the analysis of the problem of Win10 disappearing after taking a screenshot. Analysis of the problem after win10 takes a picture and it flashes and disappears 1. Check where the screenshot is saved: When you use the Win+PrtSc (PrintScreen) key combination to take a screenshot, the screenshot is usually saved in the C:\Users\YourUsername\Pictures\Screenshots folder. please

Hello everyone, have you ever encountered the situation where the Windows 10 Task Manager keeps crashing? This function helps us a lot, allowing us to quickly see all running tasks, which is very convenient to use, right? However, some friends said that they encountered this problem and didn’t know how to solve it, so let me share with you the specific solution! Solution to Win10 Task Manager crash 1. First, press and hold the "Win" + "R" keys on the keyboard to open Run, enter "regedit" and press the Enter key. 2. Expand the folders and find "HKEY_CURRENT_USERSoftwareMicros

In win10 system, hot search is one of the more practical methods, but sometimes it can cause certain troubles. So how to turn off hot search? Let’s take a look below! Step 1: Open the Settings app First, click on the Windows icon in the lower left corner of the screen and select the Settings app. Step 2: Enter "Personalization" settings In the "Settings" app, click the "Personalization" option. Step 3: Select the “Search” option In the “Personalization” settings, select the “Search” option. Step 4: Turn off popular searches. In the "Search" option, find the option "Show popular searches in search" and turn it off. Professional Tool Recommendation 1. Xiaozhi Soso Xiaozhi Soso—Quick Search and One-Click Positioning—Professional Computer Search Tool
